Using Measurements to Clear up the Cable Controversy GA S REGULAR Menu Lifewire Tech for Humans Newsletter! Search Close GO Home Theater & Entertainment > TV & Displays 98 98 people found this article helpful

Using Measurements to Clear up the Cable Controversy

Are more expensive cables worth the price?

By Brent Butterworth Brent Butterworth Writer University of North Texas A former Lifewire writer, Brent Butterworth's lifelong passion for audio and music has taken him from building DIY speakers to searching for the hottest new audio technologies. lifewire's editorial guidelines Updated on March 27, 2021 Tweet Share Email Tweet Share Email

In This Article

Expand Jump to a Section Using Measurements to Clear up the Cable Controversy AudioQuest vs. QED vs. 12-Gauge Shunyata vs. High-End Prototype vs. 12-Gauge Zoom View Phase Shift Do Speaker Cables Make a Difference? The effects of speaker cables on speaker performance can be measured and can show that changing speaker cables could have audible effects on the sound of a system.

Using Measurements to Clear up the Cable Controversy

A sample testing method used a Clio 10 FW audio analyzer and MIC-01 measurement microphone to measure the response of a Revel Performa3 F206 speaker in-room. The in-room measurement was required to assure that there’d be no significant environmental noise. Yes, the in-room measurement shows a lot of effects of the room acoustics, but that didn’t matter because here, since we're looking only for the difference in the measured result when we changed cables. And, just to recap the theory behind this: A speaker’s drivers and crossover components act as a complex electrical filter that’s tuned to give the speaker the desired sound. Adding resistance, in the form of a more resistive speaker cable, will change the frequencies at which the filter works and thus change the frequency response of the speaker. If the cable adds significantly more inductance or capacitance to the filter, then that, too, can affect the sound.

Test 1 AudioQuest vs QED vs 12-Gauge

In these tests, we measured the effects of different high-end cables in 10- to 12-foot lengths and compared them to the measurement with generic 12-gauge speaker cable. Because the measurements were in most cases so similar, we'll present them here three at a time, with two high-end cables vs. the generic cable. The chart here shows the generic cable (blue trace), AudioQuest Type 4 cable (red trace) and QED Silver Anniversary cable (green trace). As you can see, for the most part the differences are extremely tiny. In fact, most variances are within the normal, minor measurement-to-measurement differences you get when doing measurements of audio transducers due to trace amounts of noise, thermal fluctuations in the drivers, etc. There is a small difference below 35 Hz; the higher-end cables actually produce less bass output from the speaker below 35 Hz, although the difference is on the order of -0.2 dB. It's highly unlikely this would be audible, due to the ear's relative insensitivity in this range; to the fact that most music doesn't have much content in this range (for comparison, the lowest note on standard bass guitars and upright basses is 41 Hz); and because only large tower speakers have much output below 30 Hz. (Yes, you could add a subwoofer to go that low, but almost all of those are self-powered and thus wouldn't be affected by the speaker cable.) You'd hear a larger difference in bass response by moving your head 1 foot in any direction. We didn't get a chance to measure the electrical properties of the AudioQuest cable (the guy needed it back suddenly), but we did measure the resistance and capacitance of the QED and generic cables. (The inductance of the cables was too low for my Clio 10 FW to measure.) Generic 12-gauge
Resistance: 0.0057 Ω per ft.
Capacitance: 0.023 nF per foot QED Silver Anniversary
Resistance: 0.0085 Ω per ft.
Capacitance: 0.014 nF per foot

Test 2 Shunyata vs High-End Prototype vs 12-Gauge

This next round brought out much higher-end cable: a 1.25-inch-thick Shunyata Research Etron Anaconda and a 0.88-inch-thick prototype cable that's being developed for a high-end audio company. Both appear thicker because they use woven tubing to cover the internal wires, but still, they're both heavy and expensive. The Shunyata Reserach cable goes for about $5,000/pair. The chart here shows the generic cable (blue trace), the Shunyata Research cable (red trace) and the unnamed prototype high-end cable (green trace). Here's the electrical measurements: Shunyata Research Etron Anaconda
Resistance: 0.0020 Ω per ft.
Capacitance: 0.020 nF per foot High-End Prototype
Resistance: 0.0031 Ω per ft.
Capacitance: 0.038 nF per foot Here we start to see some differences, especially above about 2 kHz. Let's zoom in for a closer look...

Test 2 Zoom View

By expanding the magnitude (dB) scale and limiting the bandwidth, we can see that these bigger, fatter cables do produce a measurable difference in the speaker's response. The F206 is an 8-ohm speaker; the magnitude of this difference would increase with a 4-ohm speaker. It's not much of a difference — typically a boost of +0.20 dB with the Shunyata, +0.19 dB with the prototype — but it covers a range of more than three octaves. With a 4-ohm speaker, the figures should be double, so +0.40 dB for the Shunyata, +0.38 dB for the prototype. According to the research cited in the original article, low-Q (high bandwidth) resonances of 0.3 dB magnitude can be audible. So by switching from a generic cable or a smaller-gauge high-end cable to one of these larger cables, it is absolutely, definitely possible that a difference could be heard. What does that difference mean? That depends on the individual. You might or might not even notice it, and it'd be subtle to say the least. We can't speculate on whether it would improve or degrade the sound of the speaker; it would elevate the treble, and with some speakers that would be good and others it would be bad. Note that typical absorptive room acoustics treatments would have a bigger measured effect.

Test 3 Phase Shift

Out of sheer curiosity, we also did a comparison of the degree of phase shift caused by the cables, with the generic cable in blue, the Audioquest in red, the prototype in green, the QED in orange and the Shunyata in purple. As you can see above, there's no observable phase shift except at very low frequencies. We start to the see the effects below 40 Hz, and they get more visible down around 20 Hz. As noted before, these effects probably wouldn't be very audible for most people, because most music doesn't have much content at such low frequencies, and most speakers don't have a lot of output between 30 Hz. Still, we can't say with certainty that these effects would be inaudible.

So Do Speaker Cables Make a Difference

Brent Butterworth, Lifewire, 2018 What these tests show is that the people who insist you can't possibly hear a difference between two different speaker cables of reasonable gauge are wrong. It is possible to hear a difference by switching cables. Now, what would that difference mean to you? It'd definitely be subtle. As the blind comparison of generic speaker cables we did at The Wirecutter showed, even in the cases where listeners can hear a difference between cables, the desirability of that difference may change depending on the speaker you use. From these admittedly limited tests, it looks like the big differences in speaker cable performance are due primarily to the amount of resistance in a cable. The biggest differences measured were with the two cables that had substantially lower resistance than the others. So yes, speaker cables can change the sound of a system. Not by a lot. But they can definitely change the sound. Was this page helpful? Thanks for letting us know! Get the Latest Tech News Delivered Every Day Subscribe Tell us why! Other Not enough details Hard to understand Submit More from Lifewire What Is Speaker Sensitivity and What Does It Mean? The Difference Between Graphic and Parametric Equalizers How to Splice Wires for Speakers and Home Theater Systems How to Use a Speaker Switch for Easy Multi-Room Audio Sony SS-CS5 Bookshelf Speakers Review How to Connect Speakers Using Speaker Wire 7 Things to Consider Before Buying Headphones How to Choose and Install Speaker Wire Connectors The 8 Best Bluetooth Speakers for Under $50 in 2022 The 5 Best Surround Sound Speakers of 2022 How to Install and Set Up a Home Theater Receiver The 7 Best Floor Speakers of 2022 The 7 Best Bluetooth Speakers, Tested by Experts Do Speaker Cables Make a Difference for Audio Quality? Sonos Play:1 Frequency Measurements The 5 Best Center Channel Speakers of 2022 Newsletter Sign Up Newsletter Sign Up Newsletter Sign Up Newsletter Sign Up Newsletter Sign Up By clicking “Accept All Cookies”, you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts. Cookies Settings Accept All Cookies