NETGEAR WGR614 Default Password GA S REGULAR Menu Lifewire Tech for Humans Newsletter! Search Close GO Internet, Networking, & Security > Home Networking

NETGEAR WGR614 Default Password

Find your WGR614 default password and other default login info

By Tim Fisher Tim Fisher Senior Vice President & Group General Manager, Tech & Sustainability Emporia State University Tim Fisher has more than 30 years' of professional technology experience. He's been writing about tech for more than two decades and serves as the VP and General Manager of Lifewire. lifewire's editorial guidelines Updated on April 20, 2021 Tweet Share Email Tweet Share Email Home Networking Routers & Firewalls The Wireless Connection Network Hubs ISP Broadband Ethernet Installing & Upgrading Wi-Fi & Wireless The NETGEAR WGR614 router is available in 10 different versions, but all of them use password as the default password. As with most passwords, this one is case sensitive. Every version of this router also uses the default username of admin. When asked for the WGR614 password, just enter that. Although the username and password are the same for each version of this router, the first five versions (1–5) have a default IP address of 192.168.0.1; versions 6 and newer use 192.168.1.1. Netgear

If the Default Password Doesn' t Work Reset the WGR614

If password doesn't work when you log in, then it's been changed at some point to something else. Changing the default password of any device, including the WGR614, is an important security practice. The downside is that it's easy to forget. Reset the NETGEAR WGR614 router to restore the username and password to the factory defaults: Plug in the power cable and turn on the router. Turn the device around to access to the back panel, where the cables are plugged in. Look for the Reset button. If you don't see this button, check the bottom. Different routers have it located in different places. Firmly press the Reset button with something small and pointed, such as a paperclip or pencil, for 10 seconds. Wait for the router to reset. This may take between 30 and 60 seconds. Unplug the power cable. Then, reattach it after a few seconds to reboot the router. Wait 30 to 60 seconds for it to boot up. The router is now reset. Log in with the default username and password of admin and password. The IP address you use to access the login page will be different depending on the WGR614 version you have. Resetting to factory defaults resets every customization you made. If you had custom DNS servers, a wireless network, or port forwards, re-enter that information, which might involve configuring the DNS settings again, setting up an SSID and wireless password, and forwarding the ports. Check "Configuration File Management" in the WGR614 router user manual (links below) for instructions on backing up settings.

When You Can' t Access the WGR614 Router

If the default IP address doesn't give you access to the router, it most likely means that it was changed at some point. To find the correct address, you want to locate the default gateway IP using any device that's connected to the router. When you reset the WGR614, the default password is reinstated, too, not just the password. If you followed the steps above to reset the router, access the router with the default IP address. You shouldn't need to find the default gateway.

NETGEAR WGR614 Firmware and Manual Links

Every resource NETGEAR has on the WGR614 router is available on the WGR614 Support page. If you need the support page for a different version of this router, pick the right version from the Select a different version dropdown menu on that page. No matter which version you use, download the most recent firmware in the Downloads section. When downloading firmware, select the one that corresponds to the same hardware version of your WGR614. Installing the wrong firmware can cause problems with the router functionality. Here are direct links to the WGR614 manual for each version of this router: Version 1 Version 2 Version 3 Version 4 Version 5 Version 6 Version 7 Version 8 Version 9 Version 10 These NETGEAR WGR614 user manuals are in the PDF format, so you'll need a PDF reader to open them. The WGR614v4 manual is also a PDF, but it's stored in a ZIP file. Was this page helpful? Thanks for letting us know! Get the Latest Tech News Delivered Every Day Subscribe Tell us why! Other Not enough details Hard to understand Submit More from Lifewire NETGEAR WNR1000 Default Password Linksys E900 (N300) Default Password NETGEAR DGN2200 Default Password Linksys E1000 Default Password D-Link DIR-655 Default Password NETGEAR Default Password List (Updated October 2022) Linksys E4200 default password D-Link DIR-600 Default Password Linksys WRT54G2 Default Password Linksys WRT54GL Default Password Linksys Default Password List (Updated October 2022) Linksys EA2700 Default Password D-Link Default Password List (Updated October 2022) How to Find the Default IP Address of a Belkin Router D-Link DIR-605L Default Password Linksys E1200 Default Password Newsletter Sign Up Newsletter Sign Up Newsletter Sign Up Newsletter Sign Up Newsletter Sign Up By clicking “Accept All Cookies”, you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts. Cookies Settings Accept All Cookies